WittenScissor hydraulic elevatorWhat are the precautions for operation

announcer:hp323HP155335083 release time:2024-04-03 11:47:26

Hydraulic lifting platforms are widely used in factory maintenance, municipal construction, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.

Witten.A large logistics warehousing equipment service company directly operated by manufacturers with guaranteed prices and guaranteed services. Due to the fact that fixed elevators are mechanical equipment, the product quality and performance are good. Do not accept products from some manufacturers that do not meet the quality standards to avoid potential safety hazards during use.

Emergency bolts not tightened; The solution is to tighten the emergency valve.

.Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.

Connect the motor naturally to the elevator. When connecting,WittenMovable lifting mobile elevator, it is necessary to ensure that the concentricity of the elevator output shaft and the motor input shaft is consistent, and the outer flanges of the two are parallel. Inconsistent alignment can lead to motor shaft breakage or elevator gear wear.

Drain all the hydraulic oil in the oil tank, open the oil tank take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.


WittenScissor hydraulic elevatorWhat are the precautions for operation



The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, high-speed railway stations, shopping malls, and star hotels. It has a high elevation,WittenConstruction site elevator, and simple design.

Single column aluminum alloy elevator with easily recognizable operation panel flexible movement, multiple mechanical, electrical, and hydraulic safety protection, and advanced integrated hydraulic electricity

Honest service.The load capacity of goods and the tonnage of goods transported at once also affect the speed of lifting and lowering. Achieving the excellent value of the lifting platform for transporting goods is a guarantee of speed. If the weight is too heavy, it affects the speed. If the goods are too light, it also affects the normal transportation time.

This series of products has a load capacity of 0.1 to 0.8 tons, and can also be customized according to user requirements, with a load capacity of up to 10 tons.

The normally closed valve and motor are energized simultaneously; The solution is correct wiring, and the motor often closes the valve and loses power when powered on.


WittenScissor hydraulic elevatorWhat are the precautions for operation



Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.

Executive standard.Connect the motor naturally to the elevator. When connecting, it is necessary to ensure that the concentricity of the elevator output shaft and the motor input shaft is consistent, and the outer flanges of the two are parallel. Inconsistent alignment can lead to motor shaft breakage or elevator gear wear.

Ensure excellent power supply at the installation site,Witten2 ton electric elevator, install a separate distribution box, and the electrical leakage switch must meet the requirements for construction elevators when using the distribution box. If the installed construction elevator is variable frequency, the leakage switch should be compatible with the frequency converter when selecting it.

The purpose of the hydraulic lifting platform allows users to choose the power mode and configuration according to their own usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine.

Witten.4: Small scale pneumatic or electric rust removal is based on the principle of using air compression to generate friction or electromagnetic effects to polish and remove rust on the surface of spiral elevators. It can be used for precision instrument push rods or for enterprises that require micro operation of spiral elevators.

Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.

The hook of the seat belt should not be hung on unstable or moving objects.